Our booth at Guanzhou lighting fair. Welcome
MORE
【Z-IW601】A brief introduction of wearable explosion-proof lighting
by：ALLTOP
2021-04-07
[Z-IW] Brief introduction of wearable explosion-proof lighting
Application scope
Z-IW wearable explosion-proof lighting is suitable for firefighters' side headlights, which are worn during fire fighting and disaster relief.
Performance characteristics
The mounting bracket adopts elastic ring design, and the bracket can be gently installed on the helmet by pulling with both hands.
The design of the bionic vacuum plate makes the installation firmer.
The buckle design is adopted between the lamp and the bracket, and you can press it gently.
The shape breaks through the traditional lamp shape, and the tail is designed with a large switch button, which makes the operation more convenient.
The light source adopts imported LED, which has high luminous efficiency, long service life, and the average service life is up to hours.
It has three levels of light for working light, strong light and strobe signal, which can be used as illumination or long-distance signal indication.
The strong illuminance at the meter reaches above LX, and the discharge time is more than minutes; the working illuminance reaches above LX, and the discharge time is more than minutes.
The tail of the lamp is designed with a red azimuth light, which can be used to indicate the directions between firefighters and enhance the safety protection ability of firefighters.
Protection grade IP/IP, not afraid of the influence of fire water guns, can work in a variety of harsh environments, and use more reliably.
Added special function: When the personnel wear the lamp, the red azimuth light at the end of the lamp will start to flash in a static state.
Instructions for use
. Before use, insert the plug of the special charger into the charging hole on the back of the headlight for charging. The indicator light is green when charging, and it turns red when fully charged;
, press the switch on the top of the headlight for about 2 seconds, the headlight will light up; press the switch again, the light will go out;
, the lamp has the function of preventing misoperation, if the switch is pressed for less than .seconds, it will not change the lighting or extinguishing state of the lamp;
, keep pressing the switch, the light flashes alternately, it can be used for signal contact or instruction;
, The lamp can be worn in a variety of ways, including hand-held, waist-hung, hanging and head-worn. When wearing the headlight, snap the hook of the headlight into the card seat of the helmet.
Note
、It is strictly forbidden to hit or throw the headlight; if you accidentally drop the headlight into water or aqueous solution, you need to take it out and wipe it clean in time.
、Maintenance of headlights must be carried out by professionals in a safe place.
Technical parameters
Rated voltage: DC.V
Rated capacity: .AH
Rated power (LED): W
Luminous flux: Lm (strong light) \ Lm (working light)
Strobe: -HZ
Continuous working time: h (strong light)\ Lm (working light)
Charging time: h
Dimensions (length*width*height): .*.*mm
Protection level: IP
Weight: .kg
Quality Assurance
This product is strictly controlled in accordance with the ISO international quality management system standards to ensure that the product quality is higher than the national standard and fully meets the design requirements. Within a year from the date of purchase, the company is responsible for free maintenance for any failures under normal use of the product.
Application scope
Z-IW wearable explosion-proof lighting is suitable for firefighters' side headlights, which are worn during fire fighting and disaster relief.
Performance characteristics
The mounting bracket adopts elastic ring design, and the bracket can be gently installed on the helmet by pulling with both hands.
The design of the bionic vacuum plate makes the installation firmer.
The buckle design is adopted between the lamp and the bracket, and you can press it gently.
The shape breaks through the traditional lamp shape, and the tail is designed with a large switch button, which makes the operation more convenient.
The light source adopts imported LED, which has high luminous efficiency, long service life, and the average service life is up to hours.
It has three levels of light for working light, strong light and strobe signal, which can be used as illumination or long-distance signal indication.
The strong illuminance at the meter reaches above LX, and the discharge time is more than minutes; the working illuminance reaches above LX, and the discharge time is more than minutes.
The tail of the lamp is designed with a red azimuth light, which can be used to indicate the directions between firefighters and enhance the safety protection ability of firefighters.
Protection grade IP/IP, not afraid of the influence of fire water guns, can work in a variety of harsh environments, and use more reliably.
Added special function: When the personnel wear the lamp, the red azimuth light at the end of the lamp will start to flash in a static state.
Instructions for use
. Before use, insert the plug of the special charger into the charging hole on the back of the headlight for charging. The indicator light is green when charging, and it turns red when fully charged;
, press the switch on the top of the headlight for about 2 seconds, the headlight will light up; press the switch again, the light will go out;
, the lamp has the function of preventing misoperation, if the switch is pressed for less than .seconds, it will not change the lighting or extinguishing state of the lamp;
, keep pressing the switch, the light flashes alternately, it can be used for signal contact or instruction;
, The lamp can be worn in a variety of ways, including hand-held, waist-hung, hanging and head-worn. When wearing the headlight, snap the hook of the headlight into the card seat of the helmet.
Note
、It is strictly forbidden to hit or throw the headlight; if you accidentally drop the headlight into water or aqueous solution, you need to take it out and wipe it clean in time.
、Maintenance of headlights must be carried out by professionals in a safe place.
Technical parameters
Rated voltage: DC.V
Rated capacity: .AH
Rated power (LED): W
Luminous flux: Lm (strong light) \ Lm (working light)
Strobe: -HZ
Continuous working time: h (strong light)\ Lm (working light)
Charging time: h
Dimensions (length*width*height): .*.*mm
Protection level: IP
Weight: .kg
Quality Assurance
This product is strictly controlled in accordance with the ISO international quality management system standards to ensure that the product quality is higher than the national standard and fully meets the design requirements. Within a year from the date of purchase, the company is responsible for free maintenance for any failures under normal use of the product.
Custom message
Related Products
