Lighting: What are the manufacturing specifications for landscape lights?

1. The bottom diameter and bottom flange specifications of the landscape lighting street lamp should conform to the design plan. u003cbru003e u003cbru003e u003cbru003e u003cbru003e u003cbru003e u003cbru003e If required, the landscape light manufacturer shall present detailed engineering drawings of the matching products for consideration by the tenderer and design plan. u003cbru003e u003cbru003e u003cbru003e u003cbru003e u003cbru003e u003cbru003eStainless steel plate materials for landscape lighting must comply with regulations. u003cbru003e u003cbru003e u003cbru003e u003cbru003e u003cbru003e u003cbru003e 2. The interior and exterior of the landscape lighting street lamp should be treated with hot-dip galvanizing internal and external surface layer anti-corrosion treatment technology. u003cbru003e u003cbru003e u003cbru003e u003cbru003e u003cbru003e u003cbru003e The hot-dip galvanizing layer is not suitable for too thick, the surface is grayish, not smooth, and the left and right anti-corrosion process treatments should meet the relative specifications. u003cbru003e u003cbru003e u003cbru003e u003cbru003e u003cbru003e u003cbru003e Corrosion resistance test reports and quality test reports of relevant street lights should be presented during the whole process of construction. u003cbru003e u003cbru003e u003cbru003e u003cbru003e u003cbru003e u003cbru003e 3. The surface layer of the landscape lighting street lamp must be solved with colorful electrostatic spraying, and the color tone should also consider the requirements of the community owner. u003cbru003e u003cbru003e u003cbru003e u003cbru003e u003cbru003e u003cbru003e High-grade architectural paint should be used for electrostatic spraying. u003cbru003e u003cbru003e u003cbru003e u003cbru003e u003cbru003e u003cbru003e 4. Landscape lighting street lamps should be calculated according to the wind support requirements in the national industry standards and support regulations. u003cbru003e u003cbru003e u003cbru003e u003cbru003e u003cbru003e u003cbru003e In the whole process of project construction, material indications and support calculations related to street lights should be presented. u003cbru003e u003cbru003e u003cbru003e u003cbru003e u003cbru003e u003cbru003e For street lamps that are connected by electric welding with steel ring, the project contractor shall remove the welding joints before electric welding and make the welds in accordance with the regulations. u003cbru003e u003cbru003e u003cbru003e u003cbru003e u003cbru003e u003cbru003e 5. The design of hand-hole doors for general street light poles for landscape lighting should be unique. u003cbru003e u003cbru003e u003cbru003e u003cbru003e u003cbru003e u003cbru003e The door uses plasma cutting machine. u003cbru003e u003cbru003e u003cbru003e u003cbru003e u003cbru003e u003cbru003e The door of household appliances should have both the shape of the pole and the structure with better compressive strength. u003cbru003e u003cbru003e u003cbru003e u003cbru003e u003cbru003e u003cbru003e It has an effective indoor space for actual operation, and the side door is equipped with notes for installing household appliances. u003cbru003e u003cbru003e u003cbru003e u003cbru003e u003cbru003e u003cbru003e The gap between the door and the rod should not exceed one mm, with excellent moisture-proof properties. u003cbru003e u003cbru003e u003cbru003e u003cbru003e u003cbru003e u003cbru003e There is a dedicated tightening system software, with excellent anti-theft characteristics. u003cbru003e u003cbru003e u003cbru003e u003cbru003e u003cbru003e u003cbru003e The electrical equipment door needs to have a higher tolerance fit. u003cbru003e u003cbru003e u003cbru003e 6. The installation of landscape lighting street lights should comply with the relevant requirements in the installation technical specifications and safety technical specifications of the relative country. u003cbru003e u003cbru003e u003cbru003e u003cbru003e u003cbru003e u003cbru003e Before installing street lamps, choose suitable lifting equipment according to the street lamp's aspect ratio, net weight, and on-site conditions. The position of the lifting point and the moving and correcting method should be reported to the supervision engineer for approval; the street lamps should be installed vertically between each other The two positions of the equipment are checked and effective to ensure the correct position of the street lamp and the vertical shaft. u003cbru003e u003cbru003e u003cbru003e u003cbru003e u003cbru003e u003cbru003e 7. When screw connection is used for landscape lighting, the screw rod should be vertical to the intersection. There should be no gap between the plan view of the screw head and the prefabricated component. The number of sealing rings on each end should not exceed two. The length of the exposed nut shall not be less than 2 pitches. u003cbru003e u003cbru003e u003cbru003e u003cbru003e u003cbru003e u003cbru003e 8. After the installation effect of the landscape lighting street lamp is correct, the project contractor should first carry out the backfill soil compaction, and the backfill soil compaction should meet the relevant requirements. u003cbru003e u003cbru003e u003cbru003e u003cbru003e u003cbru003e u003cbru003e 9. The installation of sewage pipes for landscape lighting power engineering should meet the requirements of engineering drawings and relevant standards. u003cbru003e u003cbru003e u003cbru003e u003cbru003e u003cbru003e u003cbru003e 10. Detection of flatness of landscape lighting: After the street lamp is standing, use theodolite to detect the flatness between the pole and the level. u003cbru003e u003cbru003e u003cbru003e u003cbru003e u003cbru003e u003cbru003e 11. The overall look and feel of the landscape lighting street lamp: the shape design and specifications conform to the regulations, and the overall appearance is unique. The pole surface is smooth and uniform, and the color is uniform. u003cbru003eThe above is all the content shared by landscape lighting manufacturers.