loading

We are a leading manufacturer of solar power utilization and lighting systems                   Mob:+86 199 2801 5868

Wiring method of solar street light controller

The installation of solar street lights is also a technical activity. Generally, when installing solar street lights, professional technicians will provide technical guidance, but for users, they also need to have a certain understanding of the wiring method of solar street light controllers, because When one or two solar street lights fail, the solar street light manufacturer may not be able to provide door-to-door service due to the distance, and you need to assist the manufacturer. So what is the wiring method of the solar street light controller?

The wiring method of solar street light controller:

1. Connect the battery. Before connecting the battery, make sure the battery voltage is higher than 6V to start the controller. If the system is 24V, make sure that the battery voltage is not lower than 18V. The system voltage selection is only automatically recognized the first time the controller is turned on. When installing the insurance, pay attention that the maximum distance between the dead insurance device and the positive end of the battery is 150mm. After confirming that the wiring is correct, turn on the insurance.

2. Connect the load. The load end of the solar street light controller can be connected to DC electrical equipment with the same rated working voltage as the rated voltage of the battery, and the controller supplies power to the load with the battery voltage. Connect the positive and negative poles of the load to the load terminals of the controller. There may be voltage at the load end, so be careful when wiring to avoid short circuit. A fuse should be connected to the positive or negative lead of the load, and the fuse should not be connected during installation.

Confirm that the insurance is connected correctly after installation. If the load is connected through the switchboard, each load circuit has a separate fuse, and all load currents cannot exceed the rated current of the controller.

3. Connect the photovoltaic array. The controller can be applied to 12V.24V off-grid solar modules, and can also use grid-connected modules whose open circuit voltage does not exceed the specified maximum input voltage. The voltage of the solar street light components in the system should not be lower than the system voltage.

4. Check the connection. Check all connections again to see if the positive and negative poles of each terminal are correct and if all 6 terminals are tightened.

5. Confirm power on. When the battery supplies power to the controller and the controller starts, the battery LED indicator on the controller will light up, pay attention to observe whether it is correct.

6. After the battery is connected, the indicator light of the controller is in the state of running water. Note: If the positive and negative poles are reversed, the controller will not work.

7. After connecting the load, press the 'Adjust' button three times continuously to adjust the time and the load will light up. Note: The load cannot be short-circuited, otherwise the controller will be damaged.

8. The load is not bright, please check the load, or measure the battery voltage.

9. After connecting the photocell, the load is off, indicating that the light control is normal, otherwise, please check the photocell.

10. Testing stage:

(1) If everything is normal, the green light is always on.

(2) If the battery is under voltage, the red light is always on.

(3) The photocell has no voltage, and the yellow light is always on.

The wiring method of the solar street light controller is shared here. The solar street light is powered by crystalline silicon solar cells, maintenance-free valve-regulated sealed batteries (colloidal batteries) to store electrical energy, and ultra-bright LED lamps are used as light sources. , and is controlled by an intelligent charge and discharge controller, which is used to replace the street lamps of traditional public power lighting.

GET IN TOUCH WITH Us
recommended articles
Knowledge News & events Project
ALLTOP Cordially Invites You | Join Us at WETEX 2026 Dubai Solar PV Exhibition to Explore New Opportunities in the Middle East PV & Energy Storage Market!


Exhibition Name: WETEX 2026
Exhibition Dates: October 20–22, 2026
Venue: Dubai World Trade Centre · Dubai, UAE
ALLTOP Booth: 4C14
Warm Invitation | ALLTOP Debuts at the 140th Canton Fair, Jointly Witnessing a New Future of Green Energy

Exhibition Name: The 140th Canton Fair)
Exhibition Dates: October 15–19, 2026
Venue: China Import and Export Fair Complex, Guangzhou, China
ALLTOP Booth: Zone C · Hall 16.4 · Booths C34-C35, D08-D09
Golden Topping-Out Marks a New Milestone, Output Value Exceeds RMB 600 Million! ALLTOP Industrial Park’s 168,800 m² Project Successfully Topped Out

318 Days—Less Than a Year!

At the “Speed of Light,” from Blueprint to Topping-Out.

50.24 mu of Prime Land, 168,366 Square Meters of Intelligent Manufacturing Space,

Annual Output Value at Full Production Exceeding RMB 600 Million.

ALLTOP Speed, Formidable Strength, and a Promising Future!

Golden Topping-Out Shines, Output Value Soars
The Hype Is On! ALLTOP Draws Global Spotlight at the Solar Expo — Join Us for a Chat
SOLAR PV & ENERGY STORAGE WORLD EXPO 2026

Booth No.: 10.2· B551
Time: September 16–18
Address: China Import and Export Fair Complex, Guangzhou, China (No. 382 Yuejiang Middle Road, Haizhu District, Guangzhou)
ALLTOP UGANDA Invites You to Power and Elec Expo 2026

Exhibition Name: Power and Elec Expo 2026

Date: July 9th-11th 2026

Company Name: Alltop Engineering Uganda

Hall No.

Booth No. A45

Venue: UMA Show grounds, Multi-Purpose Hall, Kampala-Uganda
Our aim is to provide the best products and the most considerate service for customers.
About Us
Customer service