loading

We are a leading manufacturer of solar power utilization and lighting systems                   Mob:+86 199 2801 5868

What to do if the lamp holder of the landscape lamp fails

1. A small amount of damage

u003cbru003eIf only one or two lamp beads are broken, we can repair them by these two methods:

u003cbru003e1. Find the broken lamp bead, connect the metal at both ends of it with a wire, and short-circuit it. The effect of this is that most of the lamp beads can light up normally, only the broken individual lamp beads do not light up, which has little effect on the overall brightness.

u003cbru003e

u003cbru003e 2. If you have strong hands-on ability, you can go online to buy the same model of lamp beads (a large bag of ten dollars), and replace it yourself-use an electric soldering iron (a hair dryer will also work for a while) Heat the bead until the glue on the back of the old lamp bead is melted, then remove the old lamp bead with tweezers (don't use your hands, it is too hot) At the same time, install the new lamp beads while it is hot (note the positive and negative poles), and you're done!

u003cbru003e

u003cbru003e

u003cbru003e

u003cbru003e

u003cbru003eTwo, massive damage

u003cbru003e

u003cbru003e If a large number of lamp beads are damaged, it is recommended to replace the entire lamp bead board. The lamp bead board is also available online, please pay attention to three points when buying:

u003cbru003e

u003cbru003e

u003cbru003e 1. Measure the size of your own lamps;

u003cbru003e

u003cbru003e

u003cbru003e 2. Be optimistic about the appearance of the lamp bead board and the starter connector (explained later);

u003cbru003e

u003cbru003e

u003cbru003e 3. Make a note of the output power range of the starter (explained later).

u003cbru003e

u003cbru003e

u003cbru003e These three points of the new lamp bead board must be the same as the old lamp bead board-replacement of the lamp bead board is very simple. The new lamp bead board is fixed with magnets. When replacing it, remove the new lamp bead board and connect it to the connector of the starter.

u003cbru003e

u003cbru003e

u003cbru003e

u003cbru003e

u003cbru003eThe launcher is damaged

u003cbru003eMost of the LED lamp failures are caused by the starter. If the lamp is completely off, or the lamp flickers after being turned on, the starter is probably broken.

u003cbru003eThe starter cannot be repaired, so it can only be replaced with a new one, but the new starter is not expensive. Pay attention to three points when buying a new launcher:

u003cbru003e1. Pay attention to the appearance of the connector-the starter connector looks as follows (if the starter is male, the lamp bead board is female; vice versa)

u003cbru003e2. Make a note of whether your lamp can change color and several colors. The number of discolorations of the new starter must be the same as the old starter.

u003cbru003e3. Remember the output power range of the starter-a range will be marked on the starter, as long as the power of the lamp bead board is within this range

u003cbru003eIt is still very simple to replace. First, separate the starter from the lamp bead board. The starter is also fixed on the base with screws, just take it off. The new starter is also a magnet, just suck it and connect it to the lamp bead board.

GET IN TOUCH WITH Us
recommended articles
Knowledge News & events Project
ALLTOP Cordially Invites You | Join Us at WETEX 2026 Dubai Solar PV Exhibition to Explore New Opportunities in the Middle East PV & Energy Storage Market!


Exhibition Name: WETEX 2026
Exhibition Dates: October 20–22, 2026
Venue: Dubai World Trade Centre · Dubai, UAE
ALLTOP Booth: 4C14
Warm Invitation | ALLTOP Debuts at the 140th Canton Fair, Jointly Witnessing a New Future of Green Energy

Exhibition Name: The 140th Canton Fair)
Exhibition Dates: October 15–19, 2026
Venue: China Import and Export Fair Complex, Guangzhou, China
ALLTOP Booth: Zone C · Hall 16.4 · Booths C34-C35, D08-D09
Golden Topping-Out Marks a New Milestone, Output Value Exceeds RMB 600 Million! ALLTOP Industrial Park’s 168,800 m² Project Successfully Topped Out

318 Days—Less Than a Year!

At the “Speed of Light,” from Blueprint to Topping-Out.

50.24 mu of Prime Land, 168,366 Square Meters of Intelligent Manufacturing Space,

Annual Output Value at Full Production Exceeding RMB 600 Million.

ALLTOP Speed, Formidable Strength, and a Promising Future!

Golden Topping-Out Shines, Output Value Soars
The Hype Is On! ALLTOP Draws Global Spotlight at the Solar Expo — Join Us for a Chat
SOLAR PV & ENERGY STORAGE WORLD EXPO 2026

Booth No.: 10.2· B551
Time: September 16–18
Address: China Import and Export Fair Complex, Guangzhou, China (No. 382 Yuejiang Middle Road, Haizhu District, Guangzhou)
ALLTOP UGANDA Invites You to Power and Elec Expo 2026

Exhibition Name: Power and Elec Expo 2026

Date: July 9th-11th 2026

Company Name: Alltop Engineering Uganda

Hall No.

Booth No. A45

Venue: UMA Show grounds, Multi-Purpose Hall, Kampala-Uganda
You're Invited! Visit ALLTOP at Stand H1.10 – Solar & Storage Live Nigeria 2026

Event: Solar & Storage Live Nigeria 2026
Dates: July 14–15, 2026
ALLTOP Booth: Stand H1.10 (prime location – we look forward to seeing you there!)
Address: Landmark Centre, Lagos, Nigeria
Our aim is to provide the best products and the most considerate service for customers.
About Us
Customer service