loading

We are a leading manufacturer of solar power utilization and lighting systems                   Mob:+86 199 2801 5868

What is the street light

Shandong solar street lamps factory installed solar LED street lights are using optical waterproof overtime control of intelligent controller, with this equipment installed solar LED street light, we can be artificially controlled switching time of the lamp. Solar LED street lamp control

shandong solar street lamp manufacturers to install solar LED street lamp adopt intelligent waterproof controller, by light and time control. With this device after the installation of the solar led street lamp, we can manually control switching time of the lamp. Solar led street light controller is the core equipment of street lamp. It is connected to a solar panel, battery and light source. When the controller sensor to reduce voltage to set location of solar panels, it drives the solar street lamps light source. When we set the time, Assuming that 8 hours) Arrived, it will shut down light source. In addition, the solar controller has many functions, for example, it can prevent the battery charge and discharge, and to avoid damage of the battery. When the light is not on, you must first find out whether up to standard the quality of the controller. When the battery under the condition of unsaturated with lower voltage, the power supply ( Voltage) After being controlled, load is cut off. Cut off the battery voltage of a voltage in the recovery process. When it is not yet back to a certain point B ( Need to charge to return to discharge voltage) , because the value of the controller to point B without good control, when it is not yet back to this point and connected to the circuit, voltage when start working load and cut off some light. Check whether battery connection is correct, contact with the overpressure system is reliable, reliable battery connections, or the battery voltage is too high; For battery power failure, the test after the battery connection is correct and whether the battery discharge, automatic recovery over rated power load power and reduce the power consumption of the device is enough. After the button for a long time to restore, load short circuit, the fault is eliminated, the second day button or automatic recovery check whether the power equipment connected correctly, reliably test reliable connection, and automatic identification of 12 V / 24 V is correct ( With automatic identification mode) The model introduced pure electric mode ( 0) : in the absence of sunlight and illumination intensity, according to the set parameters start controller delay start signal after 10 minutes, start working load. After 10 minutes, when the sun rises, start controller delay light intensity closed, output shut down signal, load stop working. Optical fiber + control mode ( 1? 4) : the boot process is the same pure electric operation. Set to a specific time. When the load automatically shut down, set a time for 1? 14 hours. Manual mode ( 5) : in this mode, users can switch button control load, whether in the day or night. This pattern is used in some special load or debugging. Debug mode ( 6) : used for system debugging. Already check the correctness of the system installation. Optical signals when optical signals close load open load, ease of installation and debugging. Normally open mode ( 7) : to keep power load in the output state. This pattern is suitable for the need to 24 hours of electricity load. Solar led streetlight dedicated controller is generally divided into time control and light control. Half power controller used for lighting systems, such as solar led street lamp ( 。 jschindo。 com) And the solar power system. It's important to remember that the excessive charging and discharging of the battery will cause the service life of the greatly reduced.

GET IN TOUCH WITH Us
recommended articles
Knowledge News & events Project
ALLTOP Cordially Invites You | Join Us at WETEX 2026 Dubai Solar PV Exhibition to Explore New Opportunities in the Middle East PV & Energy Storage Market!


Exhibition Name: WETEX 2026
Exhibition Dates: October 20–22, 2026
Venue: Dubai World Trade Centre · Dubai, UAE
ALLTOP Booth: 4C14
Warm Invitation | ALLTOP Debuts at the 140th Canton Fair, Jointly Witnessing a New Future of Green Energy

Exhibition Name: The 140th Canton Fair)
Exhibition Dates: October 15–19, 2026
Venue: China Import and Export Fair Complex, Guangzhou, China
ALLTOP Booth: Zone C · Hall 16.4 · Booths C34-C35, D08-D09
Golden Topping-Out Marks a New Milestone, Output Value Exceeds RMB 600 Million! ALLTOP Industrial Park’s 168,800 m² Project Successfully Topped Out

318 Days—Less Than a Year!

At the “Speed of Light,” from Blueprint to Topping-Out.

50.24 mu of Prime Land, 168,366 Square Meters of Intelligent Manufacturing Space,

Annual Output Value at Full Production Exceeding RMB 600 Million.

ALLTOP Speed, Formidable Strength, and a Promising Future!

Golden Topping-Out Shines, Output Value Soars
The Hype Is On! ALLTOP Draws Global Spotlight at the Solar Expo — Join Us for a Chat
SOLAR PV & ENERGY STORAGE WORLD EXPO 2026

Booth No.: 10.2· B551
Time: September 16–18
Address: China Import and Export Fair Complex, Guangzhou, China (No. 382 Yuejiang Middle Road, Haizhu District, Guangzhou)
ALLTOP UGANDA Invites You to Power and Elec Expo 2026

Exhibition Name: Power and Elec Expo 2026

Date: July 9th-11th 2026

Company Name: Alltop Engineering Uganda

Hall No.

Booth No. A45

Venue: UMA Show grounds, Multi-Purpose Hall, Kampala-Uganda
Our aim is to provide the best products and the most considerate service for customers.
About Us
Customer service