loading

We are a leading manufacturer of solar power utilization and lighting systems                   Mob:+86 199 2801 5868

What are the service life of lamps and lanterns1

The reliability of the LED lighting lamps and lanterns, Life) Depends largely on the heat dissipation, so improve the level of heat dissipation is one of the key technologies. Mainly to solve the excess heat generated by the chip through the heat sink, heat dissipation body out, this is a very complex technical problems.

the following accounts respectively with us:

the power of the LED lamps and lanterns, which LED to consider heat dissipation, power LED need to heat dissipation. The power LED is refers to the working current is more than 100 ma of light-emitting diodes. Is the line of the ASSIST union, defined by reference to the United States, according to the existing two LED the forward voltage of typical value 2. V 1 and 3. 3 v, i. e. , the input power is more than 210 mw and 330 mw of leds are power LED, all need to consider the device heat dispersion problem, some people may have different views, but practice has proved, to improve the reliability of power LED ( Life) Consider the power LED heat dissipation problem.

heat related parameters related to the LED heat dissipation of the main parameters such as thermal resistance, moderate temperature.

thermal resistance is refers to the effective temperature of the device and the external regulation reference point temperature difference divided by the number of devices in the steady state power dissipation of the quotient. It is said the device cooling degree of the most important parameters. The heat dissipation good power LED thermal resistance & le; 10 ℃ / W, domestic reports the best thermal resistance & le; 5 ℃ / W, foreign can reach thermal resistance & le; 3 ℃ / W, such as do the level to ensure the service life of power LED.

refers to the LED junction temperature device for heating the main part of the semiconductor junction temperature. It is the LED device under the working conditions, the ability to withstand temperature value. Therefore the SSL plans to improve heat resistance target. Chip and heat resistance of phosphor is very high, the current has reached chip junction temperature under 150 ℃, the phosphor powder under 130 ℃, the basic life won't have any influence on the device. Chip phosphor higher heat resistance, the requirement of heat dissipation is low.

there are several different temperature rise of temperature, we discussed here is: shell - The environment temperature. It refers to the LED device shell ( LED lamps and lanterns can detect the most hot) The temperature and the environment ( In the light of lamps and lanterns in the plane, is apart from the lamps and lanterns is 0. 5 metres) The difference of the temperature. It is a temperature can be measured directly, and can directly reflect the LED device peripheral cooling degree, practice has proved that in the ambient temperature of 30 ℃, if measured LED tube shell for 60 ℃, the temperature rise shall be the 30 ℃, this basically ensures the service life of LED device value, such as temperature rise too high, LED light source, maintain rate will decrease greatly.

LED lamps and lanterns, heat dissipation new problems:

with the development of LED lighting products, there are two new techniques: first, in order to increase the flux of the single pipe, into the larger current density, such as mentioned below, so that the chip produce more heat, need to heat dissipation. Secondly, encapsulate the new structure, with the increase of the LED light source power, need more power LED chip set packaging together, such as lamps and lanterns of COB structure, modular, will produce more heat, the need for more effective heat dissipation structure and measures, which in turn to put forward new task heat dissipation, otherwise it will greatly affect the performance and life of LED lamps and lanterns.

and the LED lamps and lanterns, heat dissipation total effectiveness 50%, there are a lot of energy to become hot. Second, the LED large current density and modular lamps and lanterns will produce more concentrated waste heat, need a good heat dissipation.

to raise the level of heat dissipation we offer the following Suggestions: 1)

From the LED chip that is going to take the new structure, new technology, improve the LED chip junction temperature, heat resistance, heat resistance, and other materials, for the cooling requirements.

  2) , reduce the thermal resistance of LED devices, and adopts the new encapsulation structure, new technology, selection of thermal conductivity, good heat resistance, new materials, include metal adhesive materials, fluorescent powder mixed glue, etc. , between the thermal resistance & le; 10 ℃ / W or lower.

  3) , reduce the temperature, and as far as possible USES the heat dissipation material with good thermal conductivity, good vent way on the design requirements, make the heat spread out as soon as possible, demands for should be less than 30 ℃. In addition, improve the level of modular the heat dissipation of lamps and lanterns should be referred to the agenda.

  4) , there are a number of ways for heat dissipation, such as using heat pipe, of course, is very good, but should consider the cost factor, should be considered in the design of performance problems.

in addition, the design of the LED lamps and lanterns in addition to improving the efficiency of lamps and lanterns and light distribution requirements, good appearance, to improve the level of heat dissipation, USES the material with good thermal conductivity, it is reported that the cooling body coated with some nano materials, the thermal conductivity increases by 30%. In addition, want to have good mechanical properties and sealing, heat dissipation and dustproof, the rise of temperature of the requirements of LED lamps and lanterns should be 30 ℃. 【 The above content released by high lamp manufacturer to arrange for you 】

GET IN TOUCH WITH Us
recommended articles
Knowledge News & events Project
ALLTOP Cordially Invites You | Join Us at WETEX 2026 Dubai Solar PV Exhibition to Explore New Opportunities in the Middle East PV & Energy Storage Market!


Exhibition Name: WETEX 2026
Exhibition Dates: October 20–22, 2026
Venue: Dubai World Trade Centre · Dubai, UAE
ALLTOP Booth: 4C14
Warm Invitation | ALLTOP Debuts at the 140th Canton Fair, Jointly Witnessing a New Future of Green Energy

Exhibition Name: The 140th Canton Fair)
Exhibition Dates: October 15–19, 2026
Venue: China Import and Export Fair Complex, Guangzhou, China
ALLTOP Booth: Zone C · Hall 16.4 · Booths C34-C35, D08-D09
Golden Topping-Out Marks a New Milestone, Output Value Exceeds RMB 600 Million! ALLTOP Industrial Park’s 168,800 m² Project Successfully Topped Out

318 Days—Less Than a Year!

At the “Speed of Light,” from Blueprint to Topping-Out.

50.24 mu of Prime Land, 168,366 Square Meters of Intelligent Manufacturing Space,

Annual Output Value at Full Production Exceeding RMB 600 Million.

ALLTOP Speed, Formidable Strength, and a Promising Future!

Golden Topping-Out Shines, Output Value Soars
The Hype Is On! ALLTOP Draws Global Spotlight at the Solar Expo — Join Us for a Chat
SOLAR PV & ENERGY STORAGE WORLD EXPO 2026

Booth No.: 10.2· B551
Time: September 16–18
Address: China Import and Export Fair Complex, Guangzhou, China (No. 382 Yuejiang Middle Road, Haizhu District, Guangzhou)
ALLTOP UGANDA Invites You to Power and Elec Expo 2026

Exhibition Name: Power and Elec Expo 2026

Date: July 9th-11th 2026

Company Name: Alltop Engineering Uganda

Hall No.

Booth No. A45

Venue: UMA Show grounds, Multi-Purpose Hall, Kampala-Uganda
Our aim is to provide the best products and the most considerate service for customers.
About Us
Customer service