loading

We are a leading manufacturer of solar power utilization and lighting systems                   Mob:+86 199 2801 5868

The process of installing solar road lights high lamp manufacturer

Solar street lamps can be used in the process, the absorption of solar radiation into electricity use, so in the street lamp design, we need to look at the first point factors, that is the choice of street lamp battery varieties, such as today is often

solar street lights can be used in the process, the absorption of solar radiation into electricity use, so in the street lamp design, we need to look at the first point factors, that is the choice of street lamp battery varieties, such as monocrystalline and polycrystalline silicon cells in the very common today, is the price and also on the stability of each have each characteristic, by considering demand for your choice, we can get the choice you need practical lighting varieties. So, what is the process of installing solar road lights? High lamp factory below small make up comb for everyone. 1, according to the actual job site lighting needs, solar street lamps manufacturer to determine the installation position of lamps and ballasts and way, and then according to the lamps and lanterns to the ballast contact distance and ballast to contact distance 220 v power supply ready three core cable (the length of the corresponding Distance is not more than 2 meters can be used with the lamp is equipped with cable) 。 2, when lamps and lanterns to ballast contact distance of more than 2 meters, the three core cable needs to be replaced. With Allen wrench unscrew the lamp shell within six hexagon bolt, pull out the light body part, remove the lamps and lanterns with three core cable, and then press the original connection mode for the three core cable connected. 3, with a socket wrench unscrew ballast box fastening bolts on the cover, remove the cover price of solar panels, lamps and lanterns of the three core cable end through the introduction of the ballast output device introduced ballast cavity, LED street light, the red line, black line ( Or the blue one) Respectively received ballast, yellow green line 4, 5, 6, terminal blocks, and then put the gland nut and tighten. 4, three core power cables will have prepared through the introduction of the ballast input port device at one end, the introduction of ballast cavity, then L line ( Wire) , N line ( The midline) , respectively, received a ballast of ground of no. 1, 2, 3 a terminal, and the compression nut and tighten. 5, closed ballast box cover and tighten the bolt, the price of solar panels and then put the three core cable at the other end in accordance with the requirements of explosion-proof on 220 v power supply. 6, replacing light bulbs, cut off power supply first, check whether the chain hoist is hang up, and then use hex wrench unscrew the lamp shell six hex bolts, careful down of lamp body part, the body with the lamp shell, unscrew the old light bulbs with new bulbs. That is about the introduction of the process of installing solar road lights, solar street light system is a set of independent distributed power supply system, is not subject to regional restriction, not affected by power installation location, also do not need to do wiring buried pipe construction excavation road, site construction and installation is very convenient, don't need power transmission and transformation system, not consumption mains, environmentally friendly and energy saving, better comprehensive economic benefit, especially in road has been built to establish solar street lamp is very convenient.

GET IN TOUCH WITH Us
recommended articles
Knowledge News & events Project
ALLTOP Cordially Invites You | Join Us at WETEX 2026 Dubai Solar PV Exhibition to Explore New Opportunities in the Middle East PV & Energy Storage Market!


Exhibition Name: WETEX 2026
Exhibition Dates: October 20–22, 2026
Venue: Dubai World Trade Centre · Dubai, UAE
ALLTOP Booth: 4C14
Warm Invitation | ALLTOP Debuts at the 140th Canton Fair, Jointly Witnessing a New Future of Green Energy

Exhibition Name: The 140th Canton Fair)
Exhibition Dates: October 15–19, 2026
Venue: China Import and Export Fair Complex, Guangzhou, China
ALLTOP Booth: Zone C · Hall 16.4 · Booths C34-C35, D08-D09
Golden Topping-Out Marks a New Milestone, Output Value Exceeds RMB 600 Million! ALLTOP Industrial Park’s 168,800 m² Project Successfully Topped Out

318 Days—Less Than a Year!

At the “Speed of Light,” from Blueprint to Topping-Out.

50.24 mu of Prime Land, 168,366 Square Meters of Intelligent Manufacturing Space,

Annual Output Value at Full Production Exceeding RMB 600 Million.

ALLTOP Speed, Formidable Strength, and a Promising Future!

Golden Topping-Out Shines, Output Value Soars
The Hype Is On! ALLTOP Draws Global Spotlight at the Solar Expo — Join Us for a Chat
SOLAR PV & ENERGY STORAGE WORLD EXPO 2026

Booth No.: 10.2· B551
Time: September 16–18
Address: China Import and Export Fair Complex, Guangzhou, China (No. 382 Yuejiang Middle Road, Haizhu District, Guangzhou)
ALLTOP UGANDA Invites You to Power and Elec Expo 2026

Exhibition Name: Power and Elec Expo 2026

Date: July 9th-11th 2026

Company Name: Alltop Engineering Uganda

Hall No.

Booth No. A45

Venue: UMA Show grounds, Multi-Purpose Hall, Kampala-Uganda
Our aim is to provide the best products and the most considerate service for customers.
About Us
Customer service