loading

We are a leading manufacturer of solar power utilization and lighting systems                   Mob:+86 199 2801 5868

The matters of attention in the construction cable photovoltaic power generation system is analysed?

Photovoltaic engineering of cable project construction cost is compared commonly big, laying mode selection directly influence the construction cost, so the reasonable plan, the correct selection of cable, the cable is an important part of the design work. Cable cable apply the

in photovoltaic power generation project, the construction of the cable cost is compared commonly big, the choice of the ways of laying will directly affect the construction costs. Therefore, reasonable planning and correct selection of cable laying methods is an important part of the cable design. Cable laying methods should be based on engineering conditions, environmental conditions, cable specification, type, quantity, factors such as comprehensive consideration, and according to the requirements of reliable operation, convenient maintenance and technical, economic and reasonable principle to choose. Photovoltaic power generation project of dc cable laying mainly includes the buried sand brick laying, wear pipe laying, trough cable tray, cable conduit installation, tunnel installation, etc. Communication cable laying and ordinary power system installation. DC cable is mainly used for photovoltaic modules between, between group and DC female box, between mother box and inverter, with a small cross-sectional area and large quantity. Usually, the cable along the module bracket bound or buried directly through a pipe. When laying the DC cable, usually need to consider: ( 1) Using component stents as channels of cable laying and fixing parts, the connection between the cable and the component list and connecting cable between the parent box can reduce the influence of environmental factors to some extent. ( 2) To receive strength evenly in cable laying should be appropriate and should not be too tight. In general, photovoltaic place day and night temperature difference is bigger, should avoid cable fracture caused by thermal expansion and cold contraction. ( 3) For buildings on the surface of the pv cable wire, consideration should be given to the structure of the overall aesthetics. Installation position should be avoided in the walls and the sharp edge of the bracket for laying cable, so as to avoid short circuit caused by the cutting and wear on the insulating layer, or because of the shear force caused by open cut wire. Cable should also be considered at the same time, the problem such as direct lightning on the road. ( 4) Reasonable planning cable run, minimize cross and merge, laying reduce earthwork excavated volume and amount of cable project construction process. Photovoltaic power generation system of DC cable connection cable outside, most connection mode is mainly to insert the connector, can be protected through a pipe. Component bracket used for channels of cable laying and fixing device, in order to reduce the influence of environmental factors. Other cable connection looks almost the same as general electric power system.

GET IN TOUCH WITH Us
recommended articles
Knowledge News & events Project
ALLTOP Cordially Invites You | Join Us at WETEX 2026 Dubai Solar PV Exhibition to Explore New Opportunities in the Middle East PV & Energy Storage Market!


Exhibition Name: WETEX 2026
Exhibition Dates: October 20–22, 2026
Venue: Dubai World Trade Centre · Dubai, UAE
ALLTOP Booth: 4C14
Warm Invitation | ALLTOP Debuts at the 140th Canton Fair, Jointly Witnessing a New Future of Green Energy

Exhibition Name: The 140th Canton Fair)
Exhibition Dates: October 15–19, 2026
Venue: China Import and Export Fair Complex, Guangzhou, China
ALLTOP Booth: Zone C · Hall 16.4 · Booths C34-C35, D08-D09
Golden Topping-Out Marks a New Milestone, Output Value Exceeds RMB 600 Million! ALLTOP Industrial Park’s 168,800 m² Project Successfully Topped Out

318 Days—Less Than a Year!

At the “Speed of Light,” from Blueprint to Topping-Out.

50.24 mu of Prime Land, 168,366 Square Meters of Intelligent Manufacturing Space,

Annual Output Value at Full Production Exceeding RMB 600 Million.

ALLTOP Speed, Formidable Strength, and a Promising Future!

Golden Topping-Out Shines, Output Value Soars
The Hype Is On! ALLTOP Draws Global Spotlight at the Solar Expo — Join Us for a Chat
SOLAR PV & ENERGY STORAGE WORLD EXPO 2026

Booth No.: 10.2· B551
Time: September 16–18
Address: China Import and Export Fair Complex, Guangzhou, China (No. 382 Yuejiang Middle Road, Haizhu District, Guangzhou)
ALLTOP UGANDA Invites You to Power and Elec Expo 2026

Exhibition Name: Power and Elec Expo 2026

Date: July 9th-11th 2026

Company Name: Alltop Engineering Uganda

Hall No.

Booth No. A45

Venue: UMA Show grounds, Multi-Purpose Hall, Kampala-Uganda
Our aim is to provide the best products and the most considerate service for customers.
About Us
Customer service