loading

We are a leading manufacturer of solar power utilization and lighting systems                   Mob:+86 199 2801 5868

Solar street lamps wrong installation how to solve?

With the push of the new rural construction, more and more solar street lamp to replace the traditional grid street lamp. It used to be a reasonably good, but because in the actual installation without professional construction personnel for installation, many customers still following the traditional way to install solar street light, caused the lamp holder not shine after installation, or the defect with not bright light in the evening soon. Installation problems, will naturally to the normal street light can't shine, zhongshan solar lamp factory solar lighting for everybody below summarizes several wrong installation of solar street light and its solutions.

the, installation place mask too much

the solar street light is through the top solar photovoltaic panels absorb sunlight, then converted into electrical energy stored in the storage battery, night again through the battery discharge to power leds for lighting. So night can normal lighting, solar street lamps depends on solar photovoltaic panels can receive sunlight during the day, if too many obstructions around the solar street lamps, such as: the leaves can cause shade, building and so on, will affect the normal absorption and utilization of the solar surface light source, led to the decrease of the charging efficiency.

solution: when installing solar street lamps should be far away from obstructions, if can't steer clear of obstructions, to ensure that the solar photovoltaic panels in the direction of the south, no obstructions, or light time not less than 6 hours.

2, solar street lamp beside other light source

solar street light is intelligent street lamp, it can be used by photovoltaic panels relating to different dark time to adjust for the four seasons, without the need for human control. If there are other light around the photovoltaic panels, will cause the electric failure, solar street lamp light in nature cannot be normal. When installing a solar street lamp, stay away from other light sources, to avoid interference.

solution: if the solar street light has been installed, found its photovoltaic panels with light source and can't remove, should be adjusted in time control mode.

3,

some solar panels on the interior charge customer for the sake of brevity, install solar lamp indoors, such as building convenient for passing or parking in the island, carport, although these places have certain light during the day, but not meet the needs of the fully charged, the long-term development, easy to cause damage or completely damage of the battery.

solution: if you want to have sufficient light, solar street lamps will move solar photovoltaic panels to outdoor, if must solve indoor lighting, also can use, outdoor, indoor lighting separation installation.

4, photovoltaic panels towards error

install photovoltaic panels need to fix the photovoltaic panels before stem will, if only to find that after stem photovoltaic panels towards errors, will result in photovoltaic panels can't fully absorb sunlight to charge.

solution: first, to determine the direction of the LED light, and then determine the towards of photovoltaic panels, install photovoltaic panels should be installed in the direction of the sunniest when, in the domestic generally faces south, different installation capacity of the photovoltaic modules may also be affected.

5, not the correct use of solar energy street light remote control

some construction personnel is not the proper use of engineering the remote control, random and ensure that is no matter with the lights burning. In fact this is very wrong operation, at the same time of random may have set the wrong parameters, lead to abnormal light.

solution: normal solar street lamps manufacturer products has been tested before they go out all parameters of the solar street lights, such as the need to change, contact the manufacturer.

GET IN TOUCH WITH Us
recommended articles
Knowledge News & events Project
ALLTOP Cordially Invites You | Join Us at WETEX 2026 Dubai Solar PV Exhibition to Explore New Opportunities in the Middle East PV & Energy Storage Market!


Exhibition Name: WETEX 2026
Exhibition Dates: October 20–22, 2026
Venue: Dubai World Trade Centre · Dubai, UAE
ALLTOP Booth: 4C14
Warm Invitation | ALLTOP Debuts at the 140th Canton Fair, Jointly Witnessing a New Future of Green Energy

Exhibition Name: The 140th Canton Fair)
Exhibition Dates: October 15–19, 2026
Venue: China Import and Export Fair Complex, Guangzhou, China
ALLTOP Booth: Zone C · Hall 16.4 · Booths C34-C35, D08-D09
Golden Topping-Out Marks a New Milestone, Output Value Exceeds RMB 600 Million! ALLTOP Industrial Park’s 168,800 m² Project Successfully Topped Out

318 Days—Less Than a Year!

At the “Speed of Light,” from Blueprint to Topping-Out.

50.24 mu of Prime Land, 168,366 Square Meters of Intelligent Manufacturing Space,

Annual Output Value at Full Production Exceeding RMB 600 Million.

ALLTOP Speed, Formidable Strength, and a Promising Future!

Golden Topping-Out Shines, Output Value Soars
The Hype Is On! ALLTOP Draws Global Spotlight at the Solar Expo — Join Us for a Chat
SOLAR PV & ENERGY STORAGE WORLD EXPO 2026

Booth No.: 10.2· B551
Time: September 16–18
Address: China Import and Export Fair Complex, Guangzhou, China (No. 382 Yuejiang Middle Road, Haizhu District, Guangzhou)
ALLTOP UGANDA Invites You to Power and Elec Expo 2026

Exhibition Name: Power and Elec Expo 2026

Date: July 9th-11th 2026

Company Name: Alltop Engineering Uganda

Hall No.

Booth No. A45

Venue: UMA Show grounds, Multi-Purpose Hall, Kampala-Uganda
Our aim is to provide the best products and the most considerate service for customers.
About Us
Customer service