loading

We are a leading manufacturer of solar power utilization and lighting systems                   Mob:+86 199 2801 5868

Precautions and troubleshooting methods during the installation of solar street lights

Nowadays, solar lights benefit all over the world, but there are still many problems that accompany them. For example, they don’t light up after installation. This may be a problem in some aspects of assembly in addition to the problem of accessories. Although the installation is relatively simple, just assemble It also requires a certain amount of technology.

In order to avoid failure as much as possible, the solar lamp should be debugged before installation, and choose a sunny day. If it is installed on a cloudy or rainy day, it will only consume power and not charge after the lamp is turned on, which is not good for the battery, which will not reach the design. Claim. Be careful not to turn on the light on the day of installation. Connect the controller after installation, but do not connect to the load. After charging for one day the next day, connect the load in the evening, so that the battery capacity can reach a higher level. Of course, doing so will increase some labor costs. The angle of the battery panel is generally designed by the manufacturer according to the degree of inclination, so as to ensure a better charging capacity in winter. However, the direction angle is determined during installation. When the solar panel is assembled underground, it is found that the angle is deviated after the pole is erected. If it is almost the same, it is generally not adjusted. The angle deviation of the solar panel not only affects the charging, but also affects the solar panel voltage under the same illuminance, which will cause a relatively large error in the turn-on time of the solar lamp. Therefore, when assembling on the ground, try to adjust the azimuth angle of the solar panel to be consistent. Try not to shield the solar panel during installation to achieve the lighting effect.

When the solar street light fails after installation, it is generally divided into the following situations:

. There is voltage on the solar panel, but it cannot be charged, and the LEDI green light is off. Check whether the solar panel terminal interface of the controller is in reliable contact.

. The charging indicator LEDI (green light) flashes quickly. The system voltage is over-voltage. Check if the battery is open circuit or if the battery is connected reliably. Or the charging circuit is damaged.

. The load indicator LED (red light) is on, but the load is not working. Check whether the load terminal wiring is reliable.

. The load indicator LED (red light) flashes quickly, and the load is not working. The load is short-circuited.

. The load indicator LED (red light) flashes slowly, and the load is not working. The load power is too high.

. The LED is red and the load is not working. The battery voltage is protected. Please charge.

. The lamp head flashes. The cause of this failure is poor line contact, battery power loss, and serious decline in power storage. If the line is okay, replace the battery.

Of course, the failure of solar lights is not entirely caused by some human factors or environmental factors. The main reason is the design and materials of the solar street lights themselves, so the quality is king.

GET IN TOUCH WITH Us
recommended articles
Knowledge News & events Project
ALLTOP Cordially Invites You | Join Us at WETEX 2026 Dubai Solar PV Exhibition to Explore New Opportunities in the Middle East PV & Energy Storage Market!


Exhibition Name: WETEX 2026
Exhibition Dates: October 20–22, 2026
Venue: Dubai World Trade Centre · Dubai, UAE
ALLTOP Booth: 4C14
Warm Invitation | ALLTOP Debuts at the 140th Canton Fair, Jointly Witnessing a New Future of Green Energy

Exhibition Name: The 140th Canton Fair)
Exhibition Dates: October 15–19, 2026
Venue: China Import and Export Fair Complex, Guangzhou, China
ALLTOP Booth: Zone C · Hall 16.4 · Booths C34-C35, D08-D09
Golden Topping-Out Marks a New Milestone, Output Value Exceeds RMB 600 Million! ALLTOP Industrial Park’s 168,800 m² Project Successfully Topped Out

318 Days—Less Than a Year!

At the “Speed of Light,” from Blueprint to Topping-Out.

50.24 mu of Prime Land, 168,366 Square Meters of Intelligent Manufacturing Space,

Annual Output Value at Full Production Exceeding RMB 600 Million.

ALLTOP Speed, Formidable Strength, and a Promising Future!

Golden Topping-Out Shines, Output Value Soars
The Hype Is On! ALLTOP Draws Global Spotlight at the Solar Expo — Join Us for a Chat
SOLAR PV & ENERGY STORAGE WORLD EXPO 2026

Booth No.: 10.2· B551
Time: September 16–18
Address: China Import and Export Fair Complex, Guangzhou, China (No. 382 Yuejiang Middle Road, Haizhu District, Guangzhou)
ALLTOP UGANDA Invites You to Power and Elec Expo 2026

Exhibition Name: Power and Elec Expo 2026

Date: July 9th-11th 2026

Company Name: Alltop Engineering Uganda

Hall No.

Booth No. A45

Venue: UMA Show grounds, Multi-Purpose Hall, Kampala-Uganda
Our aim is to provide the best products and the most considerate service for customers.
About Us
Customer service