loading

We are a leading manufacturer of solar power utilization and lighting systems

Lighting: What preparations are needed before courtyard lamp construction?

First of all, before the courtyard lamp construction, check the materials again to see if there are any problems.

u003cbru003e

u003cbru003e

u003cbru003e First: Material requirements: The equipment, equipment and materials used should comply with the current national technical standards, and should have a product quality certificate, and the equipment should have a famous brand.

u003cbru003e

u003cbru003e

u003cbru003e Second: The courtyard lamp itself: 1. The accessories of the courtyard lamp should be complete, without mechanical damage, deformation, paint peeling, and lampshade cracking. 2. The section of the lamp cap wire should not be less than: copper wire-1.mm2; aluminum wire-2.5mm2.

u003cbru003e

u003cbru003e

u003cbru003e

u003cbru003e

u003cbru003e

u003cbru003e Third, pin insulators: 1. Porcelain parts and iron parts should be closely combined, and the iron parts should be galvanized well. 2. The enamel is smooth and free of defects such as cracks, lack of glaze, spots, burn marks, bubbles or burnout of enamel. 3. It is strictly forbidden to use sulfur-filled insulators.

u003cbru003e

u003cbru003e

u003cbru003e Fourth, insulated wires: 1. There should be no twists, bends, breaks, and insulation damage. 2. The cross section of the down conductor should not be less than: copper wire-1.5mm2; aluminum wire-2.5mm2; the rated voltage should not be less than 500V.

u003cbru003e

u003cbru003e

u003cbru003e

u003cbru003e

u003cbru003e

u003cbru003e Fifth, the lamp holder and hoop of the courtyard lamp: 1. The surface should be smooth and clean, free of defects such as cracks, burrs, flashes, sand holes, and bubbles. 2. It should be hot-dip galvanized. In case of partial peeling of zinc skin, red Zhangdan and paint should be applied after rust removal.

u003cbru003e

u003cbru003e

u003cbru003e Sixth,

u003cbru003eSixth, bolts used to install garden lights: 1. There should be no cracks, sand holes, zinc peeling and corrosion on the surface of the bolts, and the bolts and nuts should be well matched. 2. All kinds of connecting bolts on metal should have anti-loosening device, and the anti-loosing device should be well galvanized, with suitable elasticity, and the thickness should meet the requirements. In addition, check other materials, fuses, insulated wires, soft plastic tubes, rubber cloth, black tape, etc. carefully.

u003cbru003e

u003cbru003e

u003cbru003e Seventh, the main machinery and tools needed for courtyard lamp construction: 1, pulley, hand hammer, adjustable wrench, nylon rope. 2. Level, tape measure, foot buckle, seat belt, high stool, etc. Eighth, the working conditions of the courtyard lamp: 1. The lamp holder has been made. 2. The construction of the overhead line has been completed.

u003cbru003e The above is all the content shared by the garden lighting manufacturers.

GET IN TOUCH WITH Us
recommended articles
Knowledge News & events Project
If you need to cooperate with solar street lamp manufacturers, how will friends choose? I believe that after serious consideration, most of my friends will feel that manufacturers with a higher degree of reliability are more worthy of their trust.
In the process of using many equipment, we must pay attention to maintenance work, otherwise some small problems will gradually become big problems if they cannot be found in time, and then not only will it be more difficult to repair, but it will even cause complete damage to the equipment.
Traditional lighting equipment has always had the problem of consuming too much energy, which does not meet the current requirements for green environmental protection.
The current lighting equipment is not only rich in types, but also more stable in performance.
With the development of lighting, the life of lighting will be extended.
Solar street lights are a new type of environmentally friendly and energy-saving products.
During the actual use of equipment such as high pole lights, you may consider more maintenance methods.
During the physical use of high pole lights, most people may not know as much about this product as we think, so how much do you know about this product? In fact, they will have different opinions on different modules.
The height of the lamp panel of the high pole lamp basically has a certain size standard, so let's find out what the height of the lamp panel of this kind of equipment is.

20 meters height

The height of the lamp panel of the high pole lamp is basically made of some lamp frames made of various steel structures.
Garden lights are definitely an indispensable part of modern landscapes.
no data
Our aim is to provide the best products and the most considerate service for customers.
About Us
Customer service
detect