loading

We are a leading manufacturer of solar power utilization and lighting systems                   Mob:+86 199 2801 5868

How to configure the solar street light

Solar street light parameters are as follows: 1, the street lamp height 6 meters, materials for Q235 steel plate, a complete set of hot dip galvanized after spray outdoor powder with high quality, adopt new technology of electrostatic coating, with FP professional building materials coatings is given priority to, can meet the customers on the product surface color and the environment coordinated to

solar street light parameters are as follows: 1, street lamp height 6 meters, materials for Q235 steel plate, a complete set of hot dip galvanized after spray outdoor powder with high quality, adopt new technology of electrostatic coating, with FP professional building materials coatings is given priority to, can satisfy the customer to the requirements of the product's surface color and the environment coordinated, and product high self-cleaning property and corrosion resistance is strong, ageing resistance, suitable for any climate environment. Processing technology on the basis of design for hot-dip zinc coating, make the product performance is greatly improved, has reached the most stringent AAMA2605. The requirements of the 2005, other indicators have reached or exceed the requirements of the relevant GB.

50 years service life 2, the light source for LED, lamp bead with imported chip, super bright, high photosynthetic efficiency, 110 - 120厘米/ W) , the low light failure ( 20000 hours of less than 16%) , high power LED street lamp light source, special light distribution design, life 50000 hours 3, solar panels, with high conversion efficiency of polycrystalline silicon slice, ensure the solar cell components power is insufficient, the service life of 25 years main characteristics: ( 1) , components, design according to the international electrotechnical commission IEC: 1215:1993 standard requirements for design, with 36 or 72 pieces polycrystalline silicon solar cells in series to form various types of 12 v and 24 v components. This component can be used in all kinds of household photovoltaic system, independent photovoltaic power station and grid photovoltaic power station, etc. Component material s cell: the polysilicon solar cell. Battery of reflective film to enhance plasma chemical vapor deposition of silicon nitride film, is blue. The average conversion efficiency over 16% of the battery. S component frame: component frame is made by anodic oxidation of high quality aluminum alloy frame, the surface of alumina membrane thickness for

25 microns. Component frame is equipped with four groups of convenient installation and a set screw hole to hole, fully meet the requirements of international authoritative organization certification. S toughened glass: the surface of the component USES toughened glass, its thickness is 3 mm, most of the wavelengths of light transmittance is greater than 92%. S packaging materials: anti-aging EVA components imported from abroad ( Ethylene - Poly (vinyl acetate) And weatherability good quality TPT ( Composite fluorine plastic) Laminated material. S junction box: solar power components of the junction box is according to the current international market requirements for design and manufacturing, adopted high quality PP

as a junction box shell and inner insulation materials, silver plated copper electrode materials as the terminal. Junction box has good sealing and waterproofing performance. 4, battery: valve control type sealed gel and maintenance-free battery, with high energy density, fully sealed structure, long service life, high reliability and good service for the customer provides the more convenient. Product features: * free maintenance without rehydration * to adapt to the environment temperature is wide - Service life is long, 30 to 45 ℃ * NP is 3 - 5 years, GM can amount to 15 years safety explosion-proof * * no free liquid electrolyte, and its side 90 degrees can still use * small internal resistance, uniformity in the current discharge characteristic good * * charged factory, easy to use * unique formula, restore good performance battery deep discharge structure (1) : the battery terminals for high hardness lead alloy or copper silver plated terminals, good corrosion resistance, good conductivity and high strength. (2) the shell: the ABS shell, adhesive and heat sealing, which is especially suited for vibration is big, the environment temperature change is big. Require special long battery life. (3) sealant: using three sealing technology, the first layer of lead set welding seal, with plugging porous sealant seal after pressure testing, finally USES the red and black rubber seal, ensure the battery acid seeping defect will not occur during use. (4) the relief valve: the acidproof heat-resisting performance of epdm rubber, ensure the battery during the use of safety and reliability. (5) plate, the plate grid with good corrosion resistance of lead calcium alloy tin Quito yuan. 6 diaphragm: the acid of super fine glass fiber thermal performance is good, is to prevent negative short circuit, maintain the electrolyte, repressed plate surface, prevent the active material loss. Battery performance: (1) large current discharge performance: NP series battery USES the thin plate, the positive plate thickness in 2. 4 - 2. Between 9 mm

, at the same time, high hole rate of active material formula, plate is greater than surface area, and it is suitable for large current discharge. (2) life expectancy: NP series battery USES the thin plate, the positive grid corrosion resistant performance is relatively poor, relatively short battery life, when the ambient temperature of 25 + 5 ℃, for 5 - For eight years. (3) sealed reaction efficiency: NP series battery plate thin, piece more, specific surface area is big, easy to seal reaction. The small battery chamber at the same time, general sealed reaction efficiency of 98% or higher. 5, microcomputer controller, solar dedicated microcomputer controller, embedded optical, time control, overcharge, discharge, lightning protection electric protection function. Minimum 5 years of life main features: 1, USES the single chip microcomputer, and specialized software, realize the intelligent control; 2,

using the battery discharge rate fixed features accurate discharge control. End of the discharge voltage is the control point by the discharge rate curve correction, eliminate the pure voltage controlled discharge of not accuracy, in line with the inherent characteristics of battery, at the end of the different discharge rate has different voltage. 3, with the charge and discharge, electrical short circuit protection, overload protection, automatic control for the protection of the unique meter; The above protection are not damage any parts, not burn insurance;

GET IN TOUCH WITH Us
recommended articles
Knowledge News & events Project
ALLTOP Cordially Invites You | Join Us at WETEX 2026 Dubai Solar PV Exhibition to Explore New Opportunities in the Middle East PV & Energy Storage Market!


Exhibition Name: WETEX 2026
Exhibition Dates: October 20–22, 2026
Venue: Dubai World Trade Centre · Dubai, UAE
ALLTOP Booth: 4C14
Warm Invitation | ALLTOP Debuts at the 140th Canton Fair, Jointly Witnessing a New Future of Green Energy

Exhibition Name: The 140th Canton Fair)
Exhibition Dates: October 15–19, 2026
Venue: China Import and Export Fair Complex, Guangzhou, China
ALLTOP Booth: Zone C · Hall 16.4 · Booths C34-C35, D08-D09
Golden Topping-Out Marks a New Milestone, Output Value Exceeds RMB 600 Million! ALLTOP Industrial Park’s 168,800 m² Project Successfully Topped Out

318 Days—Less Than a Year!

At the “Speed of Light,” from Blueprint to Topping-Out.

50.24 mu of Prime Land, 168,366 Square Meters of Intelligent Manufacturing Space,

Annual Output Value at Full Production Exceeding RMB 600 Million.

ALLTOP Speed, Formidable Strength, and a Promising Future!

Golden Topping-Out Shines, Output Value Soars
The Hype Is On! ALLTOP Draws Global Spotlight at the Solar Expo — Join Us for a Chat
SOLAR PV & ENERGY STORAGE WORLD EXPO 2026

Booth No.: 10.2· B551
Time: September 16–18
Address: China Import and Export Fair Complex, Guangzhou, China (No. 382 Yuejiang Middle Road, Haizhu District, Guangzhou)
ALLTOP UGANDA Invites You to Power and Elec Expo 2026

Exhibition Name: Power and Elec Expo 2026

Date: July 9th-11th 2026

Company Name: Alltop Engineering Uganda

Hall No.

Booth No. A45

Venue: UMA Show grounds, Multi-Purpose Hall, Kampala-Uganda
Our aim is to provide the best products and the most considerate service for customers.
About Us
Customer service