loading

We are a leading manufacturer of solar power utilization and lighting systems                   Mob:+86 199 2801 5868

Garden light manufacturers talk about the packaging of the basic components of garden lights

In the garden lamp sheath line, the blue core represents the negative pole, and the red core represents the positive pole. This rule applies to the connection of solar street lights. Wrap the light pole assembly with an air film cushion with a width of 60cm. The crimping part of the air film cushion is one-sixth of its width (ie 10cm). The joint of the air film cushion needs to be wrapped with remote power tape for 3 times, and then use Straw ropes are wound with an interval of 100±10mm. Strip the sheath of about 200mm from the sheath wire at the lower end of the upper pole assembly, and then mark the 'solar cell module' mark on both ends of the solar cell module sheath wire for the garden lamp, and make sure that the mark is clear and not easy to fall off . In the courtyard lamp, use a wire stripper to strip the 30mm wire skin of the prepared solar battery module wire to the battery module end, pass the wire core through the hook of the thin iron wire and fold it back, then tighten the wire core, and then use the insulating tape to tighten the wire The core and the thin iron wire are firmly fixed. Pull the iron wire at the top of the upper light pole to take out the component wire and leave a margin of 500mm~1000mm. Reel the component wire at the bottom end of the upper light pole and tie it with a 200mm nylon cable tie. Put it into the upper light pole, and fix the component wire at the top of the upper light pole on the light pole. There are generally two sheath wires for solar cell modules. Therefore, two wires should be pre-threaded when pre-threading the wires, and then the jacket wires should be worn one by one. After the courtyard lamp wears a solar cell module sheath line, mark the two ends of the sheath line and fix the upper end immediately.

GET IN TOUCH WITH Us
recommended articles
Knowledge News & events Project
ALLTOP Cordially Invites You | Join Us at WETEX 2026 Dubai Solar PV Exhibition to Explore New Opportunities in the Middle East PV & Energy Storage Market!


Exhibition Name: WETEX 2026
Exhibition Dates: October 20–22, 2026
Venue: Dubai World Trade Centre · Dubai, UAE
ALLTOP Booth: 4C14
Warm Invitation | ALLTOP Debuts at the 140th Canton Fair, Jointly Witnessing a New Future of Green Energy

Exhibition Name: The 140th Canton Fair)
Exhibition Dates: October 15–19, 2026
Venue: China Import and Export Fair Complex, Guangzhou, China
ALLTOP Booth: Zone C · Hall 16.4 · Booths C34-C35, D08-D09
Golden Topping-Out Marks a New Milestone, Output Value Exceeds RMB 600 Million! ALLTOP Industrial Park’s 168,800 m² Project Successfully Topped Out

318 Days—Less Than a Year!

At the “Speed of Light,” from Blueprint to Topping-Out.

50.24 mu of Prime Land, 168,366 Square Meters of Intelligent Manufacturing Space,

Annual Output Value at Full Production Exceeding RMB 600 Million.

ALLTOP Speed, Formidable Strength, and a Promising Future!

Golden Topping-Out Shines, Output Value Soars
The Hype Is On! ALLTOP Draws Global Spotlight at the Solar Expo — Join Us for a Chat
SOLAR PV & ENERGY STORAGE WORLD EXPO 2026

Booth No.: 10.2· B551
Time: September 16–18
Address: China Import and Export Fair Complex, Guangzhou, China (No. 382 Yuejiang Middle Road, Haizhu District, Guangzhou)
ALLTOP UGANDA Invites You to Power and Elec Expo 2026

Exhibition Name: Power and Elec Expo 2026

Date: July 9th-11th 2026

Company Name: Alltop Engineering Uganda

Hall No.

Booth No. A45

Venue: UMA Show grounds, Multi-Purpose Hall, Kampala-Uganda
Our aim is to provide the best products and the most considerate service for customers.
About Us
Customer service