loading

We are a leading manufacturer of solar power utilization and lighting systems                   Mob:+86 199 2801 5868

Explain the wiring sequence of solar street light controller in detail

Nowadays, most rural areas across the country have installed solar street lights, but there are still some rural areas that have not installed them. At present, most of the lithium battery solar street lights used on the market are simple to install and can be plugged in and used. However, some regional engineering requirements are to use solar street lights that use colloidal batteries as batteries. At this time, solar panels, solar lamps and batteries need to be wired to the solar street light controller. The order is very important, as long as you make any mistakes. The wiring sequence of the controller will cause the solar street lamp to fail to light up. Therefore, it is extremely important for the purchaser to understand the solar street light controller in detail. The following editor will briefly talk to you.

The wiring sequence of the solar street light controller should be: first connect the load (negative) of all components, then connect the positive electrode of the colloidal battery and solar lamp, and finally connect the positive electrode of the solar panel. What we need to pay attention to here is that after the gel battery is connected, the idle indicator of the solar controller will be on. After one minute, the discharge indicator will be on and the load will be turned on. Finally, connect the solar panel, and the solar street light controller will enter the corresponding working state according to the intensity of the light. If the solar panel has charging current, the charging indicator of the solar controller will be on, and the solar street light is in the charging state. At this time, the entire solar street light system is normal, and the wiring of the solar controller should not be changed at will. You can check the working status of the entire solar street light system according to the working indicator of the solar controller.

Finally, the editor would like to remind everyone that solar street light controllers are divided into boost and buck controllers. Different solar street lamp configurations, different light source wattages are matched with different controllers. Therefore, when purchasing, you must confirm the specific configuration parameters with the solar street light manufacturer to avoid the purchased solar street light from not lighting due to the controller, then the gain is not worth the loss.

GET IN TOUCH WITH Us
recommended articles
Knowledge News & events Project
ALLTOP Cordially Invites You | Join Us at WETEX 2026 Dubai Solar PV Exhibition to Explore New Opportunities in the Middle East PV & Energy Storage Market!


Exhibition Name: WETEX 2026
Exhibition Dates: October 20–22, 2026
Venue: Dubai World Trade Centre · Dubai, UAE
ALLTOP Booth: 4C14
Warm Invitation | ALLTOP Debuts at the 140th Canton Fair, Jointly Witnessing a New Future of Green Energy

Exhibition Name: The 140th Canton Fair)
Exhibition Dates: October 15–19, 2026
Venue: China Import and Export Fair Complex, Guangzhou, China
ALLTOP Booth: Zone C · Hall 16.4 · Booths C34-C35, D08-D09
Golden Topping-Out Marks a New Milestone, Output Value Exceeds RMB 600 Million! ALLTOP Industrial Park’s 168,800 m² Project Successfully Topped Out

318 Days—Less Than a Year!

At the “Speed of Light,” from Blueprint to Topping-Out.

50.24 mu of Prime Land, 168,366 Square Meters of Intelligent Manufacturing Space,

Annual Output Value at Full Production Exceeding RMB 600 Million.

ALLTOP Speed, Formidable Strength, and a Promising Future!

Golden Topping-Out Shines, Output Value Soars
The Hype Is On! ALLTOP Draws Global Spotlight at the Solar Expo — Join Us for a Chat
SOLAR PV & ENERGY STORAGE WORLD EXPO 2026

Booth No.: 10.2· B551
Time: September 16–18
Address: China Import and Export Fair Complex, Guangzhou, China (No. 382 Yuejiang Middle Road, Haizhu District, Guangzhou)
ALLTOP UGANDA Invites You to Power and Elec Expo 2026

Exhibition Name: Power and Elec Expo 2026

Date: July 9th-11th 2026

Company Name: Alltop Engineering Uganda

Hall No.

Booth No. A45

Venue: UMA Show grounds, Multi-Purpose Hall, Kampala-Uganda
Our aim is to provide the best products and the most considerate service for customers.
About Us
Customer service