loading

We are a leading manufacturer of solar power utilization and lighting systems                   Mob:+86 199 2801 5868

30 w solar street light battery head inside the lamp holder

Light, large volume, stem height, during the installation process requires consideration of many external factors, therefore the installation personnel must be very cautious, energy-saving high lamp manufacturers {here is shandong 。 jschindo。 com} Beam technology for you a brief introduction about the light, the installation process

due to the large volume and height high lamp, during the installation process need to consider many external factors. Therefore, the installation personnel must be very careful. Here is shandong beam technology introduction of energy saving high lamp manufacturers, introduce light, the matters needing attention in the process of installation, hope to be of help: ( 1) When installation should be paid attention to. Must tighten connection of beam fixed nut with a wrench. Often as you can see, the light of the lamp cap due to incorrect screw prolapse, if the loss will cause personal injury. ( 2) Light, the light pole generally consists of two or three steel pipe. Two rod insertion depth of not less than 60 cm, hook position is fixed at the top, with basically three M14 or M16 screw connection. During the installation process should be noted that these three screws must be stainless steel screws, which is ignored by many high lamp manufacturers. Use common galvanized iron screw. As time goes on, the latter would be serious rust, making it difficult or impossible. ( 3) After light problems, lamp panel to raise. If installed in the light, lamp plate led lamp, the lamp at the back of the drive power is divided into zero, wire and ground wire. Wiring and grounding wire must be connected to a decorated the main cable connection in advance. If the drive power supply ground wire is not connected, in the thunderstorm weather has certain may be destroyed. ( 4) Should also pay attention to the operation of the connector. Tin wire connection must use wash, and then with insulating tape, pipe with flame retardant wax cover again, in order to avoid the wire under high temperature and rain exposed rapid aging, lead to light, short circuit. Some manufacturers don't think some plastic powder on the steel tube is insulated, the lightning rod is made of plastic powder spraying, so there was no lightning rod conductive function. If found this problem during the installation, you must notify the lightning rod, installation personnel from top to bottom at least 25 cm scrape plastic powder. Then, in the rain hat and the lightning rod of outlet, through fixed lightning rod top silk, can be to spin out the lightning rod plastic powder, thus the normal conduction. ( 5) At the same time, should be combined with some matters needing attention in installation of manufacturers. Second, it is necessary to install shock absorber, because on the way to and from large vehicles, it's easy to make the ground vibration, in the long run, street lamps will be loose. In the end, is the installation program Settings, must refer to the relevant specification, in order to avoid installation errors and can't normal use. ( 6) Each joint has a sleeve length. However, due to the manufacture and installation error and the effect of physical factors, the sleeve length have change, thus provides the maximum sleeve length and the minimum length of sleeve. ( 7) For ease of installation and may require lubrication fitting surface. Don't use lubricating oil to prevent leakage and pollution of the rod body, and to internal and external surfaces of the lubrication socket with soap and water. ( 8) Applied the necessary force should be at both ends to close the socket. ( 9) After hoisting in place of lamps and lanterns, technical personnel in charge of the light, calibration, commissioning, wiring and lighting. Professional electrician responsible for check the power supply circuit, power supply, handyman responsible for organizing construction phenomenon. ( 10) Lamps and lanterns of finished installation and debugging, after the normal lighting lamps and lanterns, technical personnel will be light, all technical data transferred to the designated professionals ( Or the unit professional electrician) Detailed guidance, light, some specific operational problems in the maintenance, and installation work. Shandong street lamp lighting factory co. , LTD. Is an enterprise specializing in the production of all kinds of lamps, such as solar street light, led street light, high lamp, lithium battery solar street lamp, garden lamp, landscape lamp, etc. , high quality and low price. Welcome new and old customers to come to consult.

GET IN TOUCH WITH Us
recommended articles
Knowledge News & events Project
ALLTOP Cordially Invites You | Join Us at WETEX 2026 Dubai Solar PV Exhibition to Explore New Opportunities in the Middle East PV & Energy Storage Market!


Exhibition Name: WETEX 2026
Exhibition Dates: October 20–22, 2026
Venue: Dubai World Trade Centre · Dubai, UAE
ALLTOP Booth: 4C14
Warm Invitation | ALLTOP Debuts at the 140th Canton Fair, Jointly Witnessing a New Future of Green Energy

Exhibition Name: The 140th Canton Fair)
Exhibition Dates: October 15–19, 2026
Venue: China Import and Export Fair Complex, Guangzhou, China
ALLTOP Booth: Zone C · Hall 16.4 · Booths C34-C35, D08-D09
Golden Topping-Out Marks a New Milestone, Output Value Exceeds RMB 600 Million! ALLTOP Industrial Park’s 168,800 m² Project Successfully Topped Out

318 Days—Less Than a Year!

At the “Speed of Light,” from Blueprint to Topping-Out.

50.24 mu of Prime Land, 168,366 Square Meters of Intelligent Manufacturing Space,

Annual Output Value at Full Production Exceeding RMB 600 Million.

ALLTOP Speed, Formidable Strength, and a Promising Future!

Golden Topping-Out Shines, Output Value Soars
The Hype Is On! ALLTOP Draws Global Spotlight at the Solar Expo — Join Us for a Chat
SOLAR PV & ENERGY STORAGE WORLD EXPO 2026

Booth No.: 10.2· B551
Time: September 16–18
Address: China Import and Export Fair Complex, Guangzhou, China (No. 382 Yuejiang Middle Road, Haizhu District, Guangzhou)
ALLTOP UGANDA Invites You to Power and Elec Expo 2026

Exhibition Name: Power and Elec Expo 2026

Date: July 9th-11th 2026

Company Name: Alltop Engineering Uganda

Hall No.

Booth No. A45

Venue: UMA Show grounds, Multi-Purpose Hall, Kampala-Uganda
Our aim is to provide the best products and the most considerate service for customers.
About Us
Customer service