loading

We are a leading manufacturer of solar power utilization and lighting systems                   Mob:+86 199 2801 5868

12 m single arm solar street light configuration tables

Solar led street lamp installation solar panels must be towards the south, remember to use the compass to determine direction; Solar street light in front of the square there can be no tall buildings or trees covered the sun all day; LED yard lamps before first use, should be in the sun

when installing solar LED street lamp, solar panels must be toward the south, remember to use the compass to determine direction; Solar street lamps not all day in front of the square there are tall buildings or trees; LED courtyard lamp before first use, charge for two days, in the sun for long-term to supplement the battery self-discharge; Installed components should be careful when handling solar led courtyard lamp, it is strictly prohibited to collision and percussion, lest damage; All the screw terminal etc. LED solar street lamps should tighten without looseness, reliable connection. LED street lamp solar modules, solar cells and solar energy should be paid attention to the polarity of the controller. Garden light battery compartments shall be sealed to prevent water entering, ventilation pipe ( Outlet pipe) Should be open, keep the battery warehouse ventilation, dry and clean; Solar lights around the battery compartment shall be filled with sand, in order to make sure the battery has good working temperature in winter; Due to the different light source power and different illumination time, led lights must be in strict accordance with the corresponding wiring diagram connection; Change the solar energy light source, type and power must be the same as the original factory configuration. It is forbidden to change with the factory configuration different models of power and light source, or to extend the time of lighting; Maintenance, when open the access door, forbidden smoking or solar light emitting diode lamp lit at the door. Because the battery will release a small amount of hydrogen, if see flame might explode; Because each lighting system is an independent unit of work, so the solar street light switch is normal. In order to fully guarantee the light-emitting diodes, thermal conductivity and thermal requirements, guarantee its service life, we street lamp lighting factory [ 。 jschindo。 com] Apply directly to the led street lamp of light emitting diode encapsulation secondary optical design. Make the light uniformity, better solved the problem of the bad led street light glare, to ensure the safety of drivers on the road. LED street lamp design has wide input voltage and constant current for the LED work. That is to say, don't need power grid volatility, the service life of the lamp brightness and not being affected by the fluctuation of the power grid. With temperature compensation and the technology of constant current led street lamp base design. The no brightness leds lamps delay process, after electrify to reach normal brightness. Light emitting diode lamp chromogenic rate more than 80%. It can make drivers to better identify obstacles in roads and road environment, reduce the number of traffic accidents, reduce the driver's visual fatigue. Light-emitting diodes (leds) using eutectic welding encapsulation, high reliability. To ensure the leds work longer hours. High brightness led, high luminous efficiency, high efficiency power supply. Traditional road lighting does not need high power light source and the low efficiency drive power supply, fully embodies the advantages of energy saving. Led light source is non-polluting materials and uv - The infrared radiation. Make a significant contribution to environmental protection.

GET IN TOUCH WITH Us
recommended articles
Knowledge News & events Project
ALLTOP Cordially Invites You | Join Us at WETEX 2026 Dubai Solar PV Exhibition to Explore New Opportunities in the Middle East PV & Energy Storage Market!


Exhibition Name: WETEX 2026
Exhibition Dates: October 20–22, 2026
Venue: Dubai World Trade Centre · Dubai, UAE
ALLTOP Booth: 4C14
Warm Invitation | ALLTOP Debuts at the 140th Canton Fair, Jointly Witnessing a New Future of Green Energy

Exhibition Name: The 140th Canton Fair)
Exhibition Dates: October 15–19, 2026
Venue: China Import and Export Fair Complex, Guangzhou, China
ALLTOP Booth: Zone C · Hall 16.4 · Booths C34-C35, D08-D09
Golden Topping-Out Marks a New Milestone, Output Value Exceeds RMB 600 Million! ALLTOP Industrial Park’s 168,800 m² Project Successfully Topped Out

318 Days—Less Than a Year!

At the “Speed of Light,” from Blueprint to Topping-Out.

50.24 mu of Prime Land, 168,366 Square Meters of Intelligent Manufacturing Space,

Annual Output Value at Full Production Exceeding RMB 600 Million.

ALLTOP Speed, Formidable Strength, and a Promising Future!

Golden Topping-Out Shines, Output Value Soars
The Hype Is On! ALLTOP Draws Global Spotlight at the Solar Expo — Join Us for a Chat
SOLAR PV & ENERGY STORAGE WORLD EXPO 2026

Booth No.: 10.2· B551
Time: September 16–18
Address: China Import and Export Fair Complex, Guangzhou, China (No. 382 Yuejiang Middle Road, Haizhu District, Guangzhou)
ALLTOP UGANDA Invites You to Power and Elec Expo 2026

Exhibition Name: Power and Elec Expo 2026

Date: July 9th-11th 2026

Company Name: Alltop Engineering Uganda

Hall No.

Booth No. A45

Venue: UMA Show grounds, Multi-Purpose Hall, Kampala-Uganda
Our aim is to provide the best products and the most considerate service for customers.
About Us
Customer service