loading

We are a leading manufacturer of solar power utilization and lighting systems                   Mob:+86 199 2801 5868

Lamp posts of two factors

6 m high above the light pole in the fox buried after welding machine, welding ends, namely fluently and can present a big error, the longer the light pole joint deviation, the greater the more than 10 m is more obvious, joint they distort 180 degrees, this is precisely the reason why

6 m high above the light pole in the fox buried after welding machine, welding ends, namely fluently and can present a big error, the longer the light pole joint deviation, the greater the was more obvious than 10 meters, joint they distort 180 degrees, what causes this? It also in many ways.

light pole plate after cutting of the longitudinal cutting machine, be on one side of the shear due to rub out of the cutter for extrusion, there is a high pressure accumulator to hide. Fox this force will be buried under the high quantity of heat of welding to released, that is not on one side of the shear will be released by the side of the shear force pulling in the past, eventually leading to weld distortion.

steel thicker, More than 4 mm) Rarely will not appear this kind of circumstance, even like a light, every day in 10 meters, but few of weld distortion would happen. Because the thicker steel plate itself will naturally straight, and buried the fox not easy to cause the temperature is too high, around the weld natural storage when shear force is not easy to be released also won't appear the phenomenon of distortion.

when light pole production technology before mentioned question on the weld bead is not straight, the factors of straight is comprehensive, such as not straight cutting plate, coil rod bending plate two head feed inequality, buried fox was not correct. 。 。

a, cutting board, longitudinal cutting board to cut twice, which is steel plate on both sides of positive and negative each cut a knife, the purpose is to bury a fox when welding steel plate on either side of the force can mutual confluence, pull side walk do not side can largely avoid weld rotation.

2, joint: roll bending machine lamp pole do not immediately after the fox, but with the joint machine extrusion joint straightening, and straightening the good weld with welding point, every one the best. 5 m check it, so that light pole and correct weld will be solder joint force, when the fox buried must not deformation.

in the cause of problem occurred mainly related to process, omitted some link is bound to be a bad influence on the result. In other words, to guarantee the effect of light pole ultimately without faults have to do a good job in every little link.

GET IN TOUCH WITH Us
recommended articles
Knowledge News & events Project
ALLTOP Cordially Invites You | Join Us at WETEX 2026 Dubai Solar PV Exhibition to Explore New Opportunities in the Middle East PV & Energy Storage Market!


Exhibition Name: WETEX 2026
Exhibition Dates: October 20–22, 2026
Venue: Dubai World Trade Centre · Dubai, UAE
ALLTOP Booth: 4C14
Warm Invitation | ALLTOP Debuts at the 140th Canton Fair, Jointly Witnessing a New Future of Green Energy

Exhibition Name: The 140th Canton Fair)
Exhibition Dates: October 15–19, 2026
Venue: China Import and Export Fair Complex, Guangzhou, China
ALLTOP Booth: Zone C · Hall 16.4 · Booths C34-C35, D08-D09
Golden Topping-Out Marks a New Milestone, Output Value Exceeds RMB 600 Million! ALLTOP Industrial Park’s 168,800 m² Project Successfully Topped Out

318 Days—Less Than a Year!

At the “Speed of Light,” from Blueprint to Topping-Out.

50.24 mu of Prime Land, 168,366 Square Meters of Intelligent Manufacturing Space,

Annual Output Value at Full Production Exceeding RMB 600 Million.

ALLTOP Speed, Formidable Strength, and a Promising Future!

Golden Topping-Out Shines, Output Value Soars
The Hype Is On! ALLTOP Draws Global Spotlight at the Solar Expo — Join Us for a Chat
SOLAR PV & ENERGY STORAGE WORLD EXPO 2026

Booth No.: 10.2· B551
Time: September 16–18
Address: China Import and Export Fair Complex, Guangzhou, China (No. 382 Yuejiang Middle Road, Haizhu District, Guangzhou)
ALLTOP UGANDA Invites You to Power and Elec Expo 2026

Exhibition Name: Power and Elec Expo 2026

Date: July 9th-11th 2026

Company Name: Alltop Engineering Uganda

Hall No.

Booth No. A45

Venue: UMA Show grounds, Multi-Purpose Hall, Kampala-Uganda
Our aim is to provide the best products and the most considerate service for customers.
About Us
Customer service