How many batteries in 20 w solar street light

In order to standardize the solar led street lamp packaging, operators must strictly carry out the following packaging requirements. Reference for line of solar led street lamp packing list chooses appropriate specifications sheath line ( In general, solar battery components sheathed wire choose 2 times; 2. 5 was, light source protection

to standardize the packing of the solar led street light, the operator must strictly carry out the following packaging requirements. According to the solar led street lamp packing list to choose the right specifications of the sheath line ( General solar energy battery components of sheath line is 2 times; 2. 5 was, light sheath line is 2 times; 1. 5mm2) And to determine the length of each sheath line. Determination of sheath line: from the solar led street lamp structure measurement required in the general assembly drawing sheathed wire length. For solar battery components sheath line, the connection end of the solar energy battery components and solar battery components should have enough margin, the other end must be the same with the flange at the bottom of the long. Light sheath line in connection with the light source side have enough margin, the other side must be the same with the bottom flange. The lamp assembly packaging 1) Wear thin wire in advance will be 16 wire inserted into the lamp assembly, on the left 300 mm allowance on both ends of the lamp assembly, use combination pliers to bend on the thin wire at the bottom of the lamp. Solar cell module in prepared line ( One end of the module line connected to the controller of the red line in advance with insulation tape paste insulation, insulation tape winding two layers) Battery module, with sheath line to skin 30 mm wire, the wire core through the thin wire hook, line and then core is turned back, and then screw down the wire core, reoccupy insulating tape and wire line core fixed firmly. Pull the lamp on the top of the wire and lead to the assembly line of 500 mm to 1000 mm ( According to the lamp on the assembly model of identified) 。 After the assembly line winding on the bottom of the lamp, with a 200 mm cable tied tightly, lamp and put it in. On the top of the lamp assembly fixed up a lamppost. Be careful not to break when threading line. Light pole sheathed wire from the lower pole of the component with the sheath are outlined, then the strip length of about 200 mm leather sheath, on the solar battery components sheathed wire ends; The solar cell components; Mark, at the same time must ensure that the logo is clear, not easy to fall off. Note: solar energy battery components generally has two sheath line, two iron wires, so you need to wear in advance and then sheathed wire wear in smokes. Put on the solar cell components sheath after line, marking sheathed wire at both ends, and the upper end fixed immediately. On behalf of the negative electrode in the sheath line, blue core, red core on behalf of the positive electrode. The subrule is suitable for solar street light connection. On the light pole component packages, to 60 cm with width of gas film cushion package components, light pole gas film mat curly part one 6 the width of the ( The 10 cm) Joint, gas film mat the install remote power belt as three times, then the rope wraps, spacing is 100 mm; 10 mm. Light pole component packaging. With steel seal font size neat, accurately and clearly fill out street nameplate. See the lamps and lanterns shop nameplate installation method selection, type and installation specification '. Wear thin wire, wear the 16 wire into the lamp assembly, and the lamp assembly for 300 mm allowance on both ends. Thread cutting machine wire at the bottom of the light pole under bending. Put on a jacket line will be ready for one end of the line light source is connected to the light source, with wire stripper peel off 30 mm line, bottom line core through the light pole under the components of fine wire hook, then, in turn, and then the wire core and fine wire with insulation tape firmly fixed. Twitch under the lamp at the top of the wire, pull the edge for 1200 mm to 1800 mm ( According to the lamp arm structure) Light source wires, the light wire winding next at the bottom of the lamp components, and puts it into the light components. Finally, puts a thin wire in the lamp, the lamp for 300 mm allowance on both ends of the components, and fasten the wire.