Chifeng street lamps factory1

In order to standardize the solar led street lamp packaging, operators must strictly carry out the following packaging requirements. Reference for line of solar led street lamp packing list chooses appropriate specifications sheath line ( In general, solar battery components sheath line 22. 5 was, light source

to standardize the packing of the solar led street light, the operator must strictly carry out the following packaging requirements. Standby line reference solar led street lamp packing list, select the appropriate specifications sheath line ( Solar energy battery components sheath line generally choose 2 times; 2. 5 was, light sheath line is 2 times; 1. 5mm2) And make sure each heel sheathed wire length. Determination of sheath length: from solar led street lamp assembly drawing the sheath length measurement in the structure. On the other side of the solar energy battery components sheath line must be longer than the bottom flange, except in connection with the solar cell components should leave enough margin. Light at the other end of the sheath line must be same length and the bottom flange, except in connection with the light sources have enough at the end of the allowance. Lampposts component packaging 1) Will wear thin wire into the lamp pole components on in advance, will be on 16 through wire components, light pole on each end of the light pole components to set aside 300 mm allowance, with wire clamp on the thin wire is bent into a hook at the bottom of the light pole. Preparation good solar cell module line ( Red line at the end of the module connection controller in advance with insulation tape paste insulation, insulation tape winding two layers) Through side, sheathed wire connected to the battery module with stripping pliers to skin 30 mm wire, wire core rebound after the hook through the thin line, then tighten the line core, and then will wire core and the thin line with insulation tape fixed tightly. Pull the lamp on the top of the wire and take out the assembly line, to set aside 500 mm to 1000 mm allowance ( According to the shape of the assembly of the lamp on the determined) 。 After winding in the bottom of the upper beam of an assembly line, with a 200 mm cable tied tightly, and puts it into the upper beam of light. On the top of the lamp assembly fixed up a lamppost. Be careful not to break when threading line. Light pole sheathed wire from the lower pole of the components, marked by sheath line, the length is about 200 mm sheath peeling, made & other in solar modules sheathed wire ends; Solar cell module. Mark, at the same time must ensure that the logo is clear, not easy to fall off. Note: solar energy battery components generally has two sheath line, therefore should be taken before the insert wire insert two wire, and then insert the wires smokes to sheath line. In solar energy battery components after each sheathed wire is worn, marking on both ends of the sheath line immediately, and the top is fixed. On behalf of the negative electrode in the sheath line, blue core, red core on behalf of the positive electrode. The subrule is suitable for solar street light. Tie the light pole components package, light pole component winding has a width of 60 centimeters of gas film, the film pressure welding part of the mat for the width of one 6 ( The 10 cm) Joint, gas film mat the need of remote control power belt winding three times, and then the rope winding, spacing for more than 100; 10 mm. Light pole component packaging. With steel seal number neatly accurately fill in the street nameplate, the handwriting clear. Specific installation method please refer to the nameplate choose lamps and lanterns workshop, typing and installation specification '. Pre wear thin wire wear the 16 wire into the lamp pole component, the light pole components of each end with a 300 mm allowance. Clip at the bottom of the light pole will be below the fine wire bent into a hook. By sheathed wire, wire stripper strip prepared source line connected to the light source of skin 30 mm at the end of the line, the line core through the lower light pole component bottom wire hook, tighten wire core turn it over, and then will wire core and fine wire with insulation tape fixed tightly. Pull the top of the lamp power lines, remove light source wires, and set aside the allowance of 1200 mm to 1800 mm ( According to the lamp arm structure) , the light wire winding in the bottom of the lamp, and puts it into the lamp component, the light wire fixed to the top of the lamp, under the lamppost don't broken wires in the threading process. Finally, put a thin wire in a lamppost, next to set aside 300 mm allowance on both ends of the lamp components, and fasten the wire.